Christie CC70 Manual del operador Pagina 32
- Pagina / 58
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
7: Operating the SLC Xenon Console
CHRISTIE INCORPORATED 7-5
February, 1999
115 VAC
Connect three signal wires (Scope/Flat) from automation programmer to TB6-1, TB6-2,
and TB6-3. (See Item 25 in Figure A-1.) Set switch S13 to AC mode. Provide 115 VAC
to TB6-1 or TB6-4 to activate latching relay for scope/flat format.
2. Turn autofocus switch (Item 11 in Figure 6-1) to ON (1).
3. Activate automation programmer for flat position. Observe that lamp focus adjustment
moves lamp forward. If the lamp adjustment moves in reverse:
24 VDC
Exchange the position of the two wires.
115 VAC
Exchange the position of the two wires of TB6-1 and TB6-3.
After correct travel has been obtained, proceed to next step.
4. Turn Autofocus switch to OFF (0).
5. Obtain desired light level on screen for flat format by adjusting up/down, left/right, and
forward/aft switches (Items 9 in Figure 6-1).
6. Adjust flat adjustment thumbscrew (Item 18A in Figure A-1): If green light (Item 26 in
Figure A-1) is ON, turn thumbscrew counterclockwise until light goes out. If green light
is not ON, turn thumbscrew clockwise until green light comes ON. Turn thumbscrew
back and forth several times to determine exact position where green light turns ON.
This position is correct setting for flat format.
7. Activate automation for scope format. Set desired light level on screen for scope format
by adjusting up/down, left/right, and forward/aft switches (Items 9 in Figure 6-1).
8. Adjust scope adjustment thumbscrew (Item 18B in Figure A-1): If red light (Item 27 in
Figure A-1) is ON, turn thumbscrew clockwise until light goes out. If red light is not
ON, turn thumbscrew counterclockwise until red light comes on. Turn thumbscrew back
and forth several times to determine exact position where red light turns ON. This
position is correct setting for scope format.
9. Turn autofocus switch to ON (1).
10. Activate automation several times between scope and flat formats to verify that autofocus
adjustment moves to scope and flat settings as required.
11. Verify that light levels on screen stay at maximum or desired level for both scope and flat
formats.
The lamp autofocus operates only when the autofocus switch is in the ON
position. Manual lamp adjustment is possible only when the autofocus switch
is in the OFF position. All autofocus adjustments must be made with the
autofocus switch in the OFF position. The red and green lights do not light
when the Autofocus switch is in the ON position.
- Film-Tech 1
- CHRISTIE 2
- TABLE OF CONTENTS 4
- LIST OF FIGURES AND TABLES 6
- 1. INTRODUCTION 7
- 1.3. SPECIAL NOTICES 8
- 2. SAFETY PRECAUTIONS 9
- 2.2. ALLOW LAMP TO COOL 10
- 2.5. AVOID FIRE HAZARDS 11
- 3. GENERAL DESCRIPTION 12
- 4. INSTALLATION PROCEDURES 13
- SLC Series Xenon Console 14
- 4-2 CHRISTIE INCORPORATED 14
- 4: Installation Procedures 15
- CHRISTIE INCORPORATED 4-3 15
- 4-4 CHRISTIE INCORPORATED 16
- 4.3. ELECTRICAL CONNECTIONS 17
- AC Wiring Hook-Ups 18
- DC Wiring Hook-Ups 18
- 5.1. MECHANICAL ALIGNMENT 19
- Figure 5-1: Plenum, Top View 20
- CHRISTIE INCORPORATED 5-3 21
- 6. OPERATING THE SLC 22
- Figure 6-1: Control Panel 23
- CHRISTIE INCORPORATED 6-3 24
- February, 1999 25
- 6.4. TILT ADJUSTMENT 26
- 6.5. REPLACING THE LAMP 26
- 6-6 CHRISTIE INCORPORATED 27
- EFORE OPENING THE CONSOLE 28
- LEANING OPTICAL SURFACES 28
- AINTAINING OTHER SURFACES 29
- CHRISTIE INCORPORATED 7-3 30
- 7-4 CHRISTIE INCORPORATED 31
- CHRISTIE INCORPORATED 7-5 32
- 7.6. OPTIMIZER REFLECTOR 33
- 7.7. ELECTRICAL CONNECTIONS 33
- 7.8. AIRFLOW 33
- 8. TROUBLESHOOTING 34
- 8-2 CHRISTIE INCORPORATED 35
- WARRANTY 36
- W-2 CHRISTIE INCORPORATED 37
- Appendix A 38
- A-2 CHRISTIE INCORPORATED 39
- # Description Part Number 40
- A-4 CHRISTIE INCORPORATED 41
- A-6 CHRISTIE INCORPORATED 43
- SLC 20, 30 SLC 40, 45, 70 45
- Figure A-4: Control Panel 45
- CHRISTIE INCORPORATED A-11 47
- Figure A 49
- Figure A-7: Power Supply 51
- Table A-7: Power Supply 52
- Appendix B 53
- B-2 CHRISTIE INCORPORATED 54
- Appendix C: Bill of Materials 55
- CHRISTIE INCORPORATED B-3 55
- B-4 CHRISTIE INCORPORATED 56
- CHRISTIE INCORPORATED B-5 57
- Front View Side View 58
Relacionado con productos y manuales para Proyectores Christie CC70
Proyectores Christie SXGA+ Manual de usuario
(4 paginas)
(4 paginas)
Proyectores Christie CP2000-M Manual de usuario
(205 paginas)
(205 paginas)
Proyectores Christie CC50 Manual de instalación
(36 paginas)
(36 paginas)
Proyectores Christie Entero RPMWU Manual de usuario
(60 paginas)
(60 paginas)
Proyectores Christie DS+5Kc Especificaciones
(16 paginas)
(16 paginas)
Proyectores Christie Christie HDDW Manual de usuario
(24 paginas)
(24 paginas)
Proyectores Christie D4K25 Manual de usuario
(4 paginas)
(4 paginas)
Proyectores Christie Entero RPMWU Manual de usuario
(60 paginas)
(60 paginas)
Proyectores Christie 103-010100-01 Manual de usuario
(84 paginas)
(84 paginas)
Proyectores Christie DWU675-E Manual de usuario
(12 paginas)
(12 paginas)
Proyectores Christie LX400 Manual de usuario
(20 paginas)
(20 paginas)
Proyectores Christie LX601i Manual de usuario
(42 paginas)
(42 paginas)
Proyectores Christie LX900 Manual de usuario
(90 paginas)
(90 paginas)
Proyectores Christie L2K1500 Manual de usuario
(36 paginas)
(36 paginas)
ShoreLand'r PT2125AB manuels
Manuels d'utilisation et guides de l'utilisateur pour Bandes-annonces ShoreLand'r PT2125AB.
Nous fournissons des manuels en pdf 1 ShoreLand'r PT2125AB à télécharger gratuitement par type de document : Manuel de l'utilisateur
Comentarios a estos manuales